Skip to content

Setting up the booth Mac

The sound-desk Mac, your sound board feed and the audio level.

8 articles

Only a Mac set up for your church can go live. It happens automatically when an owner or administrator signs in on that Mac.

  1. On the Mac at the sound desk, a church owner or administrator signs in to Dubr with their email and password.
  2. Dubr sets the Mac up for the church and shows “This Mac is now set up for” your church.
  3. If it didn’t happen automatically, Dubr shows Set up this Mac for Sunday. Give the Mac a name under Name this Mac and choose Set up this Mac.
  • Other roles can look around but can’t set up a Mac: Ask an admin to set up this Mac. An owner or administrator only needs to sign in there once.
  • Settings → This Mac shows Ready to go live when the Mac is set up, or Not set up when it isn’t.
  • The Mac’s sign-in is kept in the macOS Keychain.

Each Mac set up for your church uses one of the active Macs your plan includes. Settings → This Mac shows how many are in use.

  1. To free a seat from the Mac itself: Settings → This Mac → Remove this Mac. Dubr signs out on that Mac.
  2. To remove another Mac: Settings → This Mac → Your church’s other Macs → Remove, or on the web, Plan & Macs → Remove.
  • A Mac that is running a service can’t be removed until it stops.
  • A removed Mac can’t go live again until an owner or administrator signs in there and chooses Set up this Mac again.
  • When every seat is in use, remove a Mac you no longer use, or upgrade for more.
  • Only owners and administrators set up and remove Macs.

Send Dubr its own mix from the sound board, the “Dubr” mix: the speaking mics and the singers, no instruments. Bring it into the Mac through an audio interface.

  1. On the board, make a mix with the pulpit and speaking mics and the singers. Leave the instruments out. If singers harmonize, ad-lib or hum a lot, keep only the worship leader’s mic from the singers.
  2. Connect that send to the Mac through your church’s USB audio interface (or the Mac’s audio input).
  3. On Live, open Live input and choose the interface. A multi-channel interface also lists each channel and an Automatic channel option that follows the strongest input.
  4. Press Test audio to check the level.
  • Don’t see your interface? Plug it in, then use the refresh icon next to the input (Refresh audio inputs).
  • Dubr never switches to another microphone on its own. If the chosen input disappears, it says so and waits for you to choose again.
  • Usually the right input is your audio interface, not the Mac’s built-in microphone.

Test audio shows a level meter and tells you whether Dubr hears the room clearly. Aim for a good level, not too quiet or too loud.

  1. On Live, choose the input, then press Test audio.
  2. Ask someone to speak at the pulpit at their normal volume.
  3. Adjust the send on the board until the meter says Good level: speech peaking between −18 and −6 dBFS, with the clip light off.
  4. Press Done.
  • No sound: check the cable, the mixer send and that the right input is chosen.
  • Too quiet: turn the mixer send up.
  • Too loud: clipping: turn the send down until the red clip light stays off.
  • Good, but close to clipping still passes; bring the send down a little to leave room for a loud moment.
  • Inside the test, turn on Listen with headphones to hear exactly what Dubr hears.
  • The test stops after 10 minutes, and it can’t run while a service is live.

Listen to input lets you hear the live input on the Mac at any time, before, during and after a service. Use headphones.

  • Choose where it plays under Plays on and set the Volume.
  • If the sound would play through speakers near a microphone, Dubr asks first, because that causes feedback.
  • If you change the Live input, turn Listen on again to hear the new one.

macOS asks once whether Dubr may use the microphone and audio inputs. Dubr needs it to hear your sound board.

  1. When you first press Start, allow Dubr in the macOS dialog.
  2. If you denied it: open System Settings → Privacy & Security → Microphone, turn on Dubr, then press Start again.

Dubr checks for updates without interrupting a live service. Install them when no service is running.

  1. Settings → This Mac → Updates shows Up to date or Update ready.
  2. Choose Check now to look for a new version, then Install and restart.
  • An update can’t install during a service. Stop interpretation first.
  • If Dubr shows Install the latest Dubr desktop app, this version can no longer connect safely. Choose Check for update, then Install and restart.

The Service check looks at the Mac itself too: power, sleep, storage and updates.

  • Keep the Mac plugged in. The check warns when it runs on battery.
  • Set the Mac to stay awake for at least 3 hours (180 minutes) before it sleeps.
  • Keep at least 2 GB of free storage.
  • Install a pending update before the service, not during it.
  • A wired internet connection is best during services.

Still stuck?

Ask AI answers from these articles in seconds. A person on the Dubr team reads every ticket and email.

Tickets open in your church’s web workspace. In the Mac app, use Settings → Support.